There have been multiple accounts created with the sole purpose of posting advertisement posts or replies containing unsolicited advertising.

Accounts which solely post advertisements, or persistently post them may be terminated.

DayOk2

@[email protected]

This profile is from a federated server and may be incomplete. Browse more on the original instance.

DayOk2 OP , to nostupidquestions in Which height should I choose for a ring?

I have some comfort fit rings, but since my knuckles are too big, the sharp edges still touch my knuckles. Only rings with extremely rounded edges (basically cylinders) do not hurt my knuckles.

DayOk2 OP , to nostupidquestions in Which height should I choose for a ring?

Hmm, can you show me your ring so that I can see what a 4 mm height ring looks like? I could not find ring heights because search engines indicate width instead, even when I search for height.

DayOk2 OP , to nostupidquestions in Which height should I choose for a ring?

No, I want the inside of the ring to be flat. I only want the edges to be rounded.

DayOk2 OP , to nostupidquestions in Which height should I choose for a ring?

The height is important because the more height it has, the more comfortable the rounded edges are. With a ring with round edges and a height of 1 mm, the edges still feel like a knife, so it is important that the height is large enough.

DayOk2 OP , to nostupidquestions in Which height should I choose for a ring?

I am talking about the height, not the width. What you said is the width, but I want to know the height. So, what is the height of your metal parts in your ring? Here is an image of the three measurements:

https://lemmy.world/pictrs/image/dbd53b96-9a98-4dcf-b124-d710e7746c67.jpeg

DayOk2 OP , to nostupidquestions in Which height should I choose for a ring?

It is not about the ring size but about the height of the metal part. The circle opening in the ring is the ring size.

DayOk2 OP , to nostupidquestions in Where can I find rings with extremely rounded edges and half cylinders stacked above a flat band?

I edited the post to add an image of a similar ring design. You can look at it.

DayOk2 OP , to nostupidquestions in Where can I find rings with extremely rounded edges and half cylinders stacked above a flat band?

I edited the post to add an image of a similar ring design. You can look at it.

DayOk2 OP , to nostupidquestions in Where can I find rings with extremely rounded edges and half cylinders stacked above a flat band?

Okay, I meant literal half cylinders that are attached to the ring so that the main band has multiple curves from these half cylinders. The edges should also have bigger cylinders in them so that the ring is comfortable to put on and take off, and so that the the small and big cylinders have the same height in the top. This is what I want as the ring design:

  • Total width: 10 mm
  • Total height: 3 mm
  • Width main band: 4 mm
  • Height main band: 2 mm
  • Width middle gray cylinder: 3 mm
  • Height middle gray cylinder: 1 mm when cut off in half or quarters so that the half cylinder can be attached to the main band
  • Width edges pale copper cylinders: 3 mm, should be attached to the edges
  • Height edges pale copper cylinders: 3 mm because the extra 1 mm should match the height of the middle gray cylinder

Is this more clear, or should I explain more?

DayOk2 OP , to nostupidquestions in Where can I find rings with extremely rounded edges and half cylinders stacked above a flat band?

Unfortunately, I do not know how to draw the design because I am bad at drawing.

DayOk2 OP , to nostupidquestions in Where can I find rings with extremely rounded edges and half cylinders stacked above a flat band?

Yes, I am talking about a finger ring.

DayOk2 OP , to nostupidquestions in Where can I find rings with extremely rounded edges and half cylinders stacked above a flat band?

No, I meant literal half cylinders that are attached to the ring so that the main band has multiple curves from these half cylinders. The edges should also have bigger cylinders in them so that the ring is comfortable to put on and take off, and so that the the small and big cylinders have the same height in the top. This is what I want as the ring design:

  • Total width: 10 mm
  • Total height: 3 mm
  • Width main band: 4 mm
  • Height main band: 2 mm
  • Width middle gray cylinder: 3 mm
  • Height middle gray cylinder: 1 mm when cut off in half or quarters so that the half cylinder can be attached to the main band
  • Width edges pale copper cylinders: 3 mm, should be attached to the edges
  • Height edges pale copper cylinders: 3 mm because the extra 1 mm should match the height of the middle gray cylinder

Is this more clear, or should I explain more?

DayOk2 OP , to nostupidquestions in How do I get over this regret about missing an interesting video opportunity?

or your fascination with ring removal is uniquely extreme.

Yes, this is the reason. I am interested in stuck rings and the process of ring removals.

DayOk2 OP , to nostupidquestions in How do I get over this regret about missing an interesting video opportunity?

Okay, but can you tell me that to make me understand?

DayOk2 OP , to nostupidquestions in How do I get over this regret about missing an interesting video opportunity?

I do neither watch porn nor want to go to PornHub, so can you tell me what happens when searching for that?

  • All
  • Subscribed
  • Moderated
  • Favorites
  • •
  • random
  • lifeLocal
  • goranko
  • All magazines
    •