There have been multiple accounts created with the sole purpose of posting advertisement posts or replies containing unsolicited advertising.

Accounts which solely post advertisements, or persistently post them may be terminated.

DayOk2

@[email protected]

This profile is from a federated server and may be incomplete. Browse more on the original instance.

DayOk2 OP ,

It is not about the ring size but about the height of the metal part. The circle opening in the ring is the ring size.

DayOk2 OP ,

I am talking about the height, not the width. What you said is the width, but I want to know the height. So, what is the height of your metal parts in your ring? Here is an image of the three measurements:

https://lemmy.world/pictrs/image/dbd53b96-9a98-4dcf-b124-d710e7746c67.jpeg

DayOk2 OP ,

The height is important because the more height it has, the more comfortable the rounded edges are. With a ring with round edges and a height of 1 mm, the edges still feel like a knife, so it is important that the height is large enough.

DayOk2 OP ,

No, I want the inside of the ring to be flat. I only want the edges to be rounded.

DayOk2 OP ,

Hmm, can you show me your ring so that I can see what a 4 mm height ring looks like? I could not find ring heights because search engines indicate width instead, even when I search for height.

DayOk2 OP ,

I have some comfort fit rings, but since my knuckles are too big, the sharp edges still touch my knuckles. Only rings with extremely rounded edges (basically cylinders) do not hurt my knuckles.

DayOk2 OP ,

No, I meant literal half cylinders that are attached to the ring so that the main band has multiple curves from these half cylinders. The edges should also have bigger cylinders in them so that the ring is comfortable to put on and take off, and so that the the small and big cylinders have the same height in the top. This is what I want as the ring design:

  • Total width: 10 mm
  • Total height: 3 mm
  • Width main band: 4 mm
  • Height main band: 2 mm
  • Width middle gray cylinder: 3 mm
  • Height middle gray cylinder: 1 mm when cut off in half or quarters so that the half cylinder can be attached to the main band
  • Width edges pale copper cylinders: 3 mm, should be attached to the edges
  • Height edges pale copper cylinders: 3 mm because the extra 1 mm should match the height of the middle gray cylinder

Is this more clear, or should I explain more?

DayOk2 OP ,

Yes, I am talking about a finger ring.

DayOk2 OP ,

Unfortunately, I do not know how to draw the design because I am bad at drawing.

DayOk2 OP ,

Okay, I meant literal half cylinders that are attached to the ring so that the main band has multiple curves from these half cylinders. The edges should also have bigger cylinders in them so that the ring is comfortable to put on and take off, and so that the the small and big cylinders have the same height in the top. This is what I want as the ring design:

  • Total width: 10 mm
  • Total height: 3 mm
  • Width main band: 4 mm
  • Height main band: 2 mm
  • Width middle gray cylinder: 3 mm
  • Height middle gray cylinder: 1 mm when cut off in half or quarters so that the half cylinder can be attached to the main band
  • Width edges pale copper cylinders: 3 mm, should be attached to the edges
  • Height edges pale copper cylinders: 3 mm because the extra 1 mm should match the height of the middle gray cylinder

Is this more clear, or should I explain more?

DayOk2 OP ,

I edited the post to add an image of a similar ring design. You can look at it.

DayOk2 OP ,

I edited the post to add an image of a similar ring design. You can look at it.

How do I get over this regret about missing an interesting video opportunity?

I regret something and could use some advice on how to move past it. Recently, I was browsing YouTube and saw a comment from someone asking for help removing a stuck ring because their finger had swelled in the morning. I responded with a possible solution. A few minutes later, I deleted that comment and reposted the same...

DayOk2 OP ,

Hello, can you tell me what is wrong with this post?

DayOk2 OP ,

I talked with this person about recording it, and they said that they were actually going to record it by using a tool that can record these kinds of footages, had I not been too late.

DayOk2 OP ,

I think the reason is that these videos are interesting to me, but I do not know why.

DayOk2 OP ,

I meant a tool that can hold a phone to record the ring removal.

DayOk2 OP ,

I recorded it a while ago, but my knuckles are too big, so the video was not that interesting. I am more interested in rings that get stuck due to swelling and fat fingers, not big knuckles.

DayOk2 OP ,

I mean, this post is about how to get rid of regret, not about forcing the person to record it.

DayOk2 OP ,

What do you mean by this? How is this related to porn?

DayOk2 OP ,

Okay, but the thing is that while I also had other regrets, they were lessened after waiting. This however, seems like it is not going to lessen at all. Even if it seems like the regret disappeared, it comes back after one or a few days. My question is how to deal exactly with missed opportunities.

DayOk2 OP ,

I still don’t understand what makes this post special.

DayOk2 OP ,

Okay, what makes this post hilarious?

DayOk2 OP ,

I recorded it a while ago, but my knuckles are too big, so the video was not that interesting. I am more interested in rings that get stuck due to swelling and fat fingers, not big knuckles.

Also, who would even want to have a stuck ring just for it to be recorded? Not everyone has the same mindset as me.

DayOk2 OP ,

Okay, I am serious. What is wrong with this post?

DayOk2 OP ,

I do neither watch porn nor want to go to PornHub, so can you tell me what happens when searching for that?

DayOk2 OP ,

Okay, but can you tell me that to make me understand?

DayOk2 OP ,

or your fascination with ring removal is uniquely extreme.

Yes, this is the reason. I am interested in stuck rings and the process of ring removals.

  • All
  • Subscribed
  • Moderated
  • Favorites
  • •
  • random
  • lifeLocal
  • goranko
  • All magazines
    •