There have been multiple accounts created with the sole purpose of posting advertisement posts or replies containing unsolicited advertising.

Accounts which solely post advertisements, or persistently post them may be terminated.

Ethernet switch only partially working

Here is the past network setup:

  • Main Router (192.168.1.2) -> Ethernet Switch -> Multiple Ethernet cables connected to wall
  • Wall -> Second Router (192.168.1.1)
  • Wall -> PC

After a blackout we thought the switch was no longer working so we replaced it with another router. The problem is the router has too few ports, not every room gets ethernet. The ethernet switch works in this configuration:

  • Main Router -> Third Router (Wi-Fi disabled) -> Ethernet cable connected to wall -> Wall -> Ethernet Splitter -> PC Under either of these configurations PC detects network but cannot reach 192.168.1.1, 192.168.1.2 or WWW:
  • Main Router -> Ethernet Switch -> PC
  • Main Router -> Ethernet Switch -> Ethernet cable connected to wall -> Wall -> PC

Windows reports “Unidentified network”, Linux tries to connect for a minute then fails. I knwo the PC isn’t bad because other devices also fail to connect. Even if I set up a static IP I cannot reach a local IP. 2nd router has IP address 192.168.1.1 because it refuses to use anything else, first router is assigned different IP so these two don’t conflict.

BlueEther ,
@BlueEther@no.lastname.nz avatar

I’m wondering if you have an incorrect gateway set or default route

BlueEther ,
@BlueEther@no.lastname.nz avatar

also, what ports on both routers are connected? are they both using “WAN” for their uplink?

mrvictory1 OP ,

WAN and LAN1 ports on router 1 is used. LAN3,4,5,6 and Uplink ports are connected on the switch. (model is Uptech SW-116) Uplink is connected to LAN1 on router 1. Other connections go to wall. I disconnected other routers, problem persists.

Decronym Bot , (edited )

Acronyms, initialisms, abbreviations, contractions, and other phrases which expand to something larger, that I’ve seen in this thread:

Fewer Letters More Letters
AP WiFi Access Point
DHCP Dynamic Host Configuration Protocol, automates assignment of IPs when connecting to a network
IP Internet Protocol

3 acronyms in this thread; the most compressed thread commented on today has 4 acronyms.

[Thread for this sub, first seen 18th Sep 2024, 08:15] [FAQ] [Full list] [Contact] [Source code]

BlueEther , (edited )
@BlueEther@no.lastname.nz avatar

As said look at DHCP clashes or " Wall -> Ethernet Splitter -> PC Under either"

What do you mean by this? The ones I know of will drop the connection to 10mb or 100mb and will on work on both “halves” at the same time*

  • see comment by @Max_P
Max_P , (edited )
@Max_P@lemmy.max-p.me avatar

Ethernet splitter

What kind of splitter? Not a hub or switch, just a passive splitter?

Those do exist to do 4x 100M links on a single pair each, but you can’t just plug those into a router or switch and get 4 ports, it still needs to eventually terminate as 4 ports on both ends.

mrvictory1 OP , (edited )

Model is Uptech SW-116, it has “Uplink” port and 16 LAN ports. It also uses external power.

Dragomus ,

Not sure if I am reading it correctly. But what ip adress is your given to your pc?

It reads to me like you have router 1 and 2 on router 1’s network but your pc is on router 2’s “internal” network… which must not be in the same 192.168.1.x range as is router 1’s network.

Put router 1 under 192.168.2.x range Then Then Router 2 with 192.168.1.x adressing should work still, and the pc should be able to talk to the router-1 network.

mrvictory1 OP ,

PC receives 192.168.1.37

vzq ,

You have three routers? Why?

Throw 2 of them out and he switches.

mrvictory1 OP ,

2nd router is used as a wireless AP, getting rid of 3rd router is exactly what I am trying to do.

vzq ,

Just to make sure you know this, routers are not switches. You might get some of them to sort behave like switches with careful configuration, but most of the time it’s asking for a lot of trouble.

just_another_person ,

Well, routers CAN be switches. OP is just not using them in the right way.

vzq ,

That’s highly dependent on the hardware. My router only has two ports.

just_another_person ,

No, just means they need to set the correct move.

486 ,
@486@lemmy.world avatar

Are you sure there is exactly one DHCP server running?

Strit ,
@Strit@lemmy.linuxuserspace.show avatar

I was thinking the same. Could be an IP conflict.

mrvictory1 OP ,

First router has DHCP enabled with range 192.168.1.20 to 192.168.1.80. Second one has “DHCP Relay” enabled with relay server set to 192.168.1.2. Third router has DHCP disabled.

just_another_person ,

That’s not how DHCP relays work.

  • All
  • Subscribed
  • Moderated
  • Favorites
  • •
  • [email protected]
  • random
  • lifeLocal
  • goranko
  • All magazines
    •